SpeedTest:
http://www.dslreports.com/stest
http://www.whatismyip.com/
http://www.dslreports.com/scan
http://www.dslreports.com/speedtestsLinksysInfo Forums
Remote SSH access and SSH tunneling with the WRT54G
PuTTY: A Free Telnet/SSH Client
CYT Device Unlock FAQ - Linksys WRTP54G, RTP300, PAP2 v2.0, and more
http://www.sipsorcery.com/
http://www.pbxes.com
http://www.sipgate.com/
http://www.sipbroker.com/
http://www.ipkall.com/
VOIP Setting on Sipura 1001 to use vbuzzer:
Line Enable: YES
SAS Enable: NO
SIP Port: 5080
Proxy: vbuzzer.com
Outbound Proxy: vbuzzer.com:80
Use Outbound Proxy: YES
User ID: (my vbuzzer user name)
Password: (my vbuzzer PW)
Nonoh.net Setting:
SIP port : 5060
Registrar : sip.nonoh.net
Proxy server : sip.nonoh.net
Outbound proxy server : leave empty
Account name : mytask99
Password : your nonoh password
Display name/number : your nonoh username or voipnumber
Stunserver (option) : stun.nonoh.net
Local access #: 647-724-5249
Dial 00-86- to call China
FreePhoneLine Setting:
http://voipfan.net/ATAs/PAP2_freephoneline.php
SIP Port: 5060
Proxy: voip.freephoneline.ca or voip2.freephoneline.ca or fplproxy.fongo.com
User ID: 14161234567
Transport: UDP
STUN/ICE: Disable
NAT Mapping Enabled: Yes
NAT Keep Alive: Yes
NAT Traversal: Enable sending Keep-Alives only:
Keep Alive Message: ‘Nat Keep Alive Msg’ = $NOTIFY or $PING
(Never use REGISTER as your Keep Alive message )
Keep Alive Interval: 20 seconds*
Use Outbound Proxy: No
Supported Codecs: g711-u (uLAW) and g729
Suggested RTP Packet size (psize): 0.020
DellVoice/Fongo Setting:
http://blog.voipdiy.com/2012/02/dell-voice-diy-byod-using-pap2t-voip.html
SIP Port: 5060 ( any port between 5060 - 5070 will work).
Proxy: sip.fongo.com
User ID: 14161234567
RTP ports: 13000-13001 ( standardized RTP port range between 10001-20000).
Voip.ms Setting:
SIP Port: 5060
Proxy: toronto.voip.ms
User ID: 138871
Comon Setting:
RTP Packet Size: 0.020
STUN Server: stunserver.org
Register Expires: 180
Bobsled
http://bobsled.com
Sipura on FWD:
Click "Advanced" at the bottom of the page.
Click "Line 2" tab, and enter the following in the available fields:
User ID: your FWD account's FWD number (e.q. 736704, 721813)
Display Name: an identifier to be displayed on callee's CallerID.
Password: your FWD account's password (e.q. YYYYY)
Set Proxy to: fwd.pulver.com
Use Outbound Proxy: Yes
Set Outbound Proxy to: fwdnat.pulver.com:5082
Click "Provisioning" tab, set
Provisioning Enable: no
Press the Submit All Changes at the bottom of the web page
SIPDiscount Setting:
username:
password:
SIP Proxy/Registrar: sip1.sipdiscount.com
SIP Outbound Proxy(Optional): sip1.sipdiscount.com
Domain(Optional): sipdiscount.com
STUN Server: stun.sipdiscount.com
VoipStunt Setting:
username: cnyouyou
password:
SIP Proxy/Registrar: sip.voipstunt.com
SIP Outbound Proxy(Optional): sip.voipstunt.com
Domain(Optional): voipstunt.com
STUN Server: stun.voipstunt.com
Local access #: 416-800-0270
Voipraider.com Setting:SIP port : 5060
Registrar : sip.Voipraider.com
Proxy server : sip.Voipraider.com
Outbound proxy server : leave empty
Account name : mytask999
Password : your password
Display name/number : your username or voipnumber
Stunserver (option) : stun.Voipraider.com
Local access #: 647-724-5249
(Using US$)
SIPphone
Username / SIP number: 17476397267
Password :
SIP Proxy : proxy01.sipphone.com:5060
SIP Domain : proxy01.sipphone.com
STUN Server : stun01.sipphone.com on:3478
VoipBuster Setting:
username:
password:
SIP Proxy/Registrar: sip.voipbuster.com :5060
SIP Outbound Proxy(Optional): sip.voipbuster.com
Domain(Optional): sip.voipbuster.com
STUN Server: stun.voipbuster.com :3478
configuration which works perfect for Sipura:
http://www.voip-info.org/wiki/view/Sipura+settings+VBuzzer
http://www.dslreports.com/forum/remark,14604325
More Voip Related:
http://www.e164.org/
http://www.voxalot.com
http://www.sipbroker.com
http://freeworlddialup.com/
http://www.voip-info.org
https://openwengo.com/ 100 minutes with open source
http://www.sipdiscount.com/ Free 1 minute per call
http://www.sipbroker.com/sipbroker/action/pstnNumbers PSTN # work with SIP Broker
http://www.vbuzzer.com
http://www.voipstunt.com/ Free 1 minute phone calls to 39 countries
PSTN # work with SIP Broker:
Toronto +1-416-548-4739
Vancouver +1-604-628-4266
Winnipeg +1-204-480-4085
Buffalo, NY +1-716-200-1692
Jersey City +1-201-984-1823
Michigan +1-616-608-0509
New York +1-646-291-2168
Seattle +1-360-526-0602
Twin Cities, MN +1-612-235-6188
When prompted, dial SIP-Code-Number or ENUM.
SIP-Code
*452 vbuzzer.com:80
*393 fwd.pulver.com (736704)
For example:
416-548-4739 wait for message, then press *393 736704
72.56.1.196
Dial Plan:
VBuzzer :
*xx |[346]11|0|00 |<:1>[2-9]xx xxx xxxxS0 |[1][2-9]xx xxx xxxxS0 |<911:14168082222>)
FPL:
*xx |[346]11|0|00 |<:1>[2-9]xx xxx xxxxS0 |[1][2-9]xx xxx xxxxS0 |<911:14168082222> |<:01186>0[1-9]xx xxxx xxxxS0 |<:01186>0[1-9]xx xxxx xxxS0 | xx.)
Nonoh:
*xx |[346]11|0|00 |<:001>[2-9]xx xxx xxxxS0 |<:00>1[2-9]xx xxx xxxxS0 |<911:14168082222> |<:0086>0[1-9]xx xxxx xxxxS0 |<:0086>0[1-9]xx xxxx xxxS0 |<01186:0086>xxx xxxx xxxxS0 | <01186:0086>xxx xxxx xxxS0 | xx.)
(*xx[3469]11000[2-9]xxxxxx1xxx[2-9]xxxxxxxxxxxxxxxxxx.)
(*xx[3469]11000[2-9]xx xxxx[0]xxx xxx xxxxxxxxxxxxxxxx xxx xxx xxxx.*xx*xx.)
(*xx[3469]11000<:1>[469][014][657]xxx xxxx1xxx xxx xxxxxxx xxxxxxx xxx xxxxx xxx xxx xxxx01186x.)
Default for PAP2:
(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)
I can make 7, 10, and 11 digit dialling for North America. I can even call my country, Turkey (+90), with only 12-digit dialing. NO MORE 011 +90 dialing.
Some other use these setting:
NAT Mapping Enabled: NO
NAT Keep Alive Enabled: NO
Proxy: vbuzzer.com:80
Outbound Proxy: Blank
Register: Yes
Register Expires: 60
Use DNS SRV: No
Proxy Fallback Intvl: 3600
Use Outbound Proxy: No
Use OB Proxy In Dialog: Yes
Make Call Without Reg: No
Ans Call Without Reg: No
DNS SRV Auto Prefix: No
Proxy Redundancy Method: Normal
Display Name: Your vBuzzer Login Username
User ID: Your vBuzzer Login Username
Password: Your Password
Use Auth ID: No
Auth ID: Blank
Preferred Codec: G711u
Register Expires 设个小点的数，比如60，120
如果你的硬IP电话机是Sipura的话，在Router上做以下两个端口映射后应该就行了
1. UDP 80
2. The UDP port range specified from SIP > RTP Parameters > RTP Port Min until SIP > RTP Parameters > RTP Port Max
Dial plan desc:
I also have VBuzzer set up on my PAP2 although I'm not using an outbound proxy. Seems to work just fine. As for the dialling local numbers, try adding this to your dial plan:
<:1416>[89][24]xxxxxS0
Ok, now the [89] represents the first digit of the local number in your calling area which can be (in my case) an 8 or a 9. Replace these numbers with whatever is appropriate for your calling area. For example: say that all local numbers within Toronto start with a 2,4,5,6 or a 9, you'd craft the first part of the dial plan as follows:
<:1416>[24569]
The second set of brackets [] represent the second digit in the phone number. This isn't necessarily required however in my case, all local numbers either have a 2 or a 4 as the second digit.
The string of x's following the bracketed numbers represent any numerical digit (0-9) which make up the balance of the local call. the 'SO' at the end means that the call should be sent 'Straight Out' on completion of dialling a local number.
Note: One number from each set of brackets + the number of x's in the string must equal the number of digits in a local call for you. For example, [9][2]xxxxx would equal a 7 digit local number. The reason for the brackets is that we want to try and make the dial plan as unambiguous as possible. If your tried dialling a local call where the first number wasn't mentioned in the first set of brackets, the dialling plan would disregard it as a local call.
FWD: Free World Dialup
http://www.freeworlddialup.com/
How to setup URI from FWD to VBUZZER?
Log on to this hidden link to your account on FWD website http://account.freeworlddialup.com/inde
Select the Active for Forwarding URL and try putting URL address like any of these two formats:
sip:vbuzzerusername@vbuzzer.com:80
sip:vbuzzer 1416 mailto:1416number@vbuzzer.com:80
怎样让你的网络电话保持正确的时间
很 多朋友都在使用网络电话，如何才能让你的来电显示记录下对方拨来的正确时间呢？大家使用的适配器大都是Linksys或者Sipura SPA系列的适配器，在这些设置里面有一项是Primary NTP Server, 把它设置为time-nw.nist.gov，Secondary设置为ntp-2.vt.edu，你就可以得到正确的时间了。另外，在Regional 设置里面有一项设置：Daylight Saving Time Rule，把它设置为start=3/2/7;end=11/1/7;save=1，这样就能保证夏时制也有准确的时间了。
wrt54g
CDF0 = wrt54g v1.0 / ADM6996L Chipset / CPU 125Mhz
CDF1 = wrt54g v1.0 / ADM6996L Chipset / CPU 125Mhz
CDF2 = wrt54g v1.1 / ADM6996L Chipset / CPU 125Mhz
CDF3 = wrt54g v1.1 / ADM6996L Chipset / CPU 125Mhz
CDF5 = wrt54g v2.0 / ADM6996L Chipset / CPU 200Mhz
CDF7 = wrt54g v2.2 / BCM5325EKQM Chipset / CPU 200Mhz
CDF8 = wrt54g v3.0 / BCM5325EKQM Chipset / CPU 200Mhz
CDF9 = wrt54g v3.1 / BCM5325EKQM Chipset / CPU 200Mhz
CDFA = wrt54g v4.0 / BCM5352E Chipset / CPU 200Mhz
CDFB = wrt54g v5.0 / BCM5352EKPB Chipset / CPU 200Mhz
http://www.hyperwrt.org/Home-Page.shtml HyperWRT firmware for the Linksys WRT54G and WRT54GS router 3.03.6 firmware hardware versions :WRT54G : V1, V1.1, V2, V2.2, V3
http://www.linksysinfo.org/modules.php?name=Content&pa=showpage&pid=33 The WRT54G Revival Guide
http://www.tomsnetworking.com/Sections-article78-page4.php
http://www.linksysinfo.org/modules.php?name=Forums&file=viewtopic&t=2946
Tips:
1. Read this How To: Setting up WDS Bridging
2. Make your gigafast is set up as a bridge.
3. If you are using WEP for your linksys. Make sure you are setting up WDS security with the proper key.
4. My recommendation is that you turn off the Gigafast DHCP server so that is always the Linksys that provides DHCP services.
The Gigafast is already assigned a default ip address of 192.168.1.254 and it will be accessable because it is in the same subnet as the linksys (192.168.1.1)
Thanks, guys. I think the problem was that I was using the "regular" MAC address rather than the Wireless MAC address. It's working now.
Here's my topology:
Cable Modem---WRT54G(A) (((--WDS+WEP--))) WRT54G(B)
On both routers the following needs to be configured:
1. Under the Wireless --> Basic Wireless Settings configuration be sure to set the following items to the same on both routers:
a. Wireless Network Mode (I selected G-Only as I have no B devices)
b. Wireless Network Name (SSID)
c. Wireless Channel
2. Under the Wireless --> Wireless Security configuration be sure to set the following items to the same on both routers:
a. Security Mode **Note, I could only get WEP to work with WDS, not WPA**
b. Default transmit key
c. WEP Encryption
d. Passphrase (Then press generate)
3. Next, you need to determine the wireless MAC address of each router. To do this goto Status --> Wireless. The MAC address will be the first item listed. Write these down for future reference.
On WRT54G(A) the following needs to be configured:
1. Under Administration --> Management --> Startup enter the following (where BB:BB:BB:BB:BB:BB is the MAC address of the wireless on WRT54G(B):
a. wl lazywds 0
b. wl wds BB:BB:BB:BB:BB:BB
Click Save and close.
On WRT54G(B) the following needs to be configured:
1. On the Setup --> Basic Configuration page be sure to set the following:
a. Configured the LAN IP address to something different than the address on WRT54G(A) such as 192.168.1.2
b. Turn off the DHCP server
2. Under Administration --> Management --> Startup enter the following (where AA:AA:AA:AA:AA:AA is the MAC address of the wireless on WRT54G(A):
a. wl lazywds 0
b. wl wds AA:AA:AA:AA:AA:AA
Click Save and close.
Now, just reboot each router. You can use the "Reboot" button on the Administration page. That's it. Simple isn't it?
